CONSTANT PRESSURE EXPERTS FOR OVER 30 YEARS

Cycle Sensor Pump Monitor: Installation Instructions (CS3PH1-500HP)

Lock out feature: To lock or unlock adjustment settings, hold up and down buttons at the same time.

Step 1: Mount the Pump Control

Mount the pump control in the desired location and wire the unit according to the appropriate wiring diagram on the following pages. Make sure all local, state, and national electrical codes are followed.

Apply power to the unit as per diagram.

Step 2: View the Current Transformer Ratio

To view the Current Transformer Ratio, press and hold the "Man. Res./CT Ratio" button. Momentarily press the "Up" button to view the present programmed CT ratio. Follow the chart below to determine the CT (current transformer) ratio, the number of wire passes through the center of the CT, and the number to program for the CT ratio setting.

Motor FLA Range CT Ratio Number of Wire Passes Program Setting
1 to 7.5 Amps 50:5 10 "5"
7.5 to 25 Amps 50:5 2 "25"
25 to 75 Amps 50:5 1 "50"
75 to 250 Amps 250:5 1 "250"
250 to 500 Amps 500:5 1 "500"

To change the CT Ratio Setting, continue to press and hold the "Manual Reset"button while pressing either the "Up" or "Down" until the display matches the appropriate CT ratio setting. Since the update time on this setting is slow, you will need to hold the "Up" or "Down" button for several seconds to change to the next number.

Step 3: Set the Current Adjustment Setting

To set the Current Adjustment Setting, insure that all water valves are closed, so that the pump will be pressurizing the tank when operating. Press and hold the "Manual Reset" button and observe the number that is being displayed by the pump control. This number represents the amp-draw of the motor. You will need to multiply this number by .95 to determine the set point.

Release the "Manual Reset" button and press and hold the "Current Adjust" button. The display will show the present Current Adjust setting. Modify this number to match the above calculated set point by pressing either the "Up" or "Down" button. Release all of the buttons when this step is completed.

Note: If the pressure switch shuts the pump down before completing this step, you will need to depressurize the system by opening a valve, and repeat the process.

Step 4: View the Dry Run Restart Delay Setting

To view the Dry Run Restart Delay Setting, push and hold the "Restart Delay"button. The display will show the number in minutes the pump will be off before automatically restarting from a dry run condition. To change this number, press either the "Up" or "Down" button until the display matches the desired restart delay setting. Release all buttons. "000" is manual reset only.

Step 5: View the Rapid Cycle Setting

To view the Rapid Cycle Setting, push and hold the "Rapid Cycle" button. The display will show the number of seconds required between pump start-ups without locking out on a rapid cycle condition. To change this number, press either the "Up" or "Down" button until the display matches the desired rapid cycle setting. Release all buttons.

Step 6: Observe the Operation of the System

Observe the operation of the system, insuring that the pump control is set correctly. If the pump control is too sensitive, reduce the "Current Adjust" setting by repeating Step 2. If the well will pump dry, insure that the pump control will shut the pump down when it breaks suction for 10 seconds. If the pump control does not shut down when the pump breaks suction, increase the under current setting by holding the "Current Adjust" button and pushing up button. Repeat this step until set.

FREE US SHIPPING (except to AK and HI) *
We do ship into Canada via UPS International or USPS. Carrier is chosen depending on product ordered.
We ship to Alaska and Hawaii via USPS.
Customers may also choose DHL International on any product.
* Shipping charges will apply on international shipments and do not include any customs fees.

Copyright © 2024 Cycle Stop Valves, Inc.